Phones answered 24/7Baltimore, MD
Call (833) 751-2102
Serving Baltimore City

Built-up and modified bitumen roofs on Baltimore buildings

Tar-and-gravel and modified bitumen systems are read ply by ply, then patched, recoated or rebuilt where they have failed.

  • Rowhouse flat and low-slope roofs
  • Wind and storm damage
  • Parapets, cornices and flashing

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Built-Up and Mod Bit

Built-Up and Modified Bitumen Roofing: what it covers

Quick answer

Built-up and modified bitumen roofing in Baltimore covers the low-slope systems that layer reinforced sheets or a polymer-modified membrane, usually finished with gravel or a coating. Baltimore Roofing routes these jobs to a local roofer who reads each ply before deciding whether to patch, recoat or rebuild.

Built-Up and Modified Bitumen Roofing illustration for Baltimore, MD

Built-up roofs are made of plies: reinforcing felts or mats set in hot or cold bitumen, then finished with a surfacing of gravel, mineral granules or a coating. Modified bitumen is a closely related family, with polymer-modified sheets that are torched, self-adhered or set in adhesive. Both are common on low-slope roofs, and both tend to fail in a recognizable order.

In Baltimore, the flat sections most often met are the roofs of attached rowhouses, which sit behind a parapet or front cornice. Those roofs are the flat or low-slope form of the attached house, and a repair or recovering job at the edge has to be scoped with the parapet in mind. The surface work itself is a matter of reading the plies beneath it.

The usual failure is rarely the top ply. It is the seam between plies where moisture has been trapped, the flashing at a wall or curb, and the surfacing that has worn thin at the low points. A roofer who works on the surface alone will see the same leak return, so the scope reads each layer before deciding what to do.

Service area
Baltimore & Baltimore City
Availability
Phones answered 24/7
Warning signs

Signs you need built-up and modified bitumen roofing

Hot-applied systems and torched sheets put open flame and hot bitumen on a roof, which creates real fire risk. Keep extinguishers on hand, watch the wind direction, and never leave a heat source unattended. Do not walk a surfacing that is soft or blistered, because it can break through to a void below. Keep the roof edge clear of stacked material, and call (833) 751-2102 before any work that involves heat.

  • Gravel or granules washed into drifts toward the drain or the low edge
  • Open laps or splits along seams where two sheets meet
  • Blisters that crack open and expose a dry, powdery layer
  • Bare patches where the surfacing has worn down to the ply beneath
  • Flashing at a wall or curb lifting away from the surface
  • Interior staining that appears in the first heavy rain after a dry spell
Options

Types and options for built-up and modified bitumen roofing

Gravel and surfacing renewal

Loose or washed-out gravel is re-spread on a sound membrane, or the surfacing is replaced where it has worn thin. Gravel holds only where it is kept off the drains, so the outlets are cleared and the edges re-finished as part of the same work.

Modified bitumen patch and seam repair

A split seam or a failed patch is repaired with a sheet of modified membrane, bonded to the sound surface and extended well past the damage. The new sheet is torched, self-adhered or set in adhesive according to the product and the conditions on the day.

Full built-up rebuild

Where the plies are failing across a broad area, the system is stripped to the deck and rebuilt in new plies, with new base flashing and a new surfacing. This is the heaviest option and the one that makes the most difference to a roof that has leaked in several places.

One call and it gets handled.

Tell us when you need someone and we book the earliest visit a built-up and modified bitumen roofing technician has, and you approve the price before any work starts.

Reading the plies before deciding anything

The number and condition of the plies decide whether a repair is enough, so the roof is read before a single sheet is cut.

A roofer probes or cuts a test point to see how the system is built. The number of plies, whether they are bonded to each other or loose, and the type of surfacing all matter. A built-up roof that has trapped moisture between plies needs that moisture addressed, because a new top ply laid over wet felt shelters the problem rather than ending it.

The reading is recorded in plain language: the layers found, the condition of each, the extent of the damage and the failure points marked on the roof. That record is the basis for the decision, and it is the document a homeowner should ask to keep.

Flashing, curbs and wall terminations

Most leaks on a built-up or modified roof start at a termination rather than in the middle of the field.

A wall termination is where the field plies turn up and meet masonry or metal. The base flashing is carried up the wall and held above the surface, with counter-flashing set into the wall over it. When that metal fails, water runs behind the base and enters the building well away from the visible surface, which is why a leak can seem to begin in the middle of a room.

Curbs around rooftop units and vent stacks are flashed on the same principle. Corners are cut and folded rather than simply overlapped, so no seam sits directly at a corner where it can open. A new flashing sheet laid over an old one without removing it tends to add a second failure line.

  • Base flashing carried up the wall and held above the surface
  • Counter-flashing set into the wall above the base
  • Curb corners cut and folded rather than overlapped at a seam
  • Drains and scuppers set level with the membrane

Recoat, repair or rebuild

The right answer depends on how much of the system is still sound, and the reading decides it.

A repair fits when the damage is local, the plies are bonded and the surfacing is still thick enough to protect them. A recoat fits when the surface has aged across the whole roof but the plies below are sound and dry. A rebuild is needed when the plies have trapped water across a broad area, when the deck is soft, or when the surfacing has worn to the bitumen in many places.

The choice should be explained with the reading in hand. A roofer who recommends a rebuild points to the plies and the moisture found, and one who recommends a recoat shows that the layers beneath are dry. Either way the homeowner can read the reasoning and ask to see the test points.

Our process

How our built-up and modified bitumen roofing visit works

  1. Survey and test the layers

    The roof is walked and test cuts are made at representative points. Each ply and its bond to the next are recorded, and any moisture reading taken is noted against the location of its test point.

  2. Mark the failure points

    Blisters, open seams, washed areas and failed terminations are marked on a plan of the roof, so the scope can say exactly which area is being addressed and why it is being addressed.

  3. Clear the drains and the surface

    Gravel and debris are cleared from the outlets, and surfacing is removed where it is failing. Loose material is swept from the work area, and the drains are checked for flow before any new membrane goes down.

  4. Repair plies, terminations and seams

    Failed plies are cut back to sound material, the deck is repaired where it is soft, and new base flashing is set at each wall and curb. New sheets are bonded to the sound field and lapped over the old surface with the seams kept clear of the corners.

  5. Surface, test and record

    The surfacing is laid or coated to the scope, the drains are tested with water, and the roof is walked to confirm the finish. A written record of the work, the plies and the flashing goes to the homeowner.

Baltimore City

Why built-up and modified bitumen roofing is different in Central Maryland

Baltimore City requires a permit before a structure is repaired, altered or rehabilitated, under Baltimore City Code, Building Code Article II section 105. A recoat or rebuild on a building is covered by that requirement, so ask whether the contractor will pull the permit before work begins.

Attached rowhouses in Baltimore often have a flat or low-slope roof behind a parapet or cornice. Where a built-up roof meets a parapet, the base flashing goes up the parapet wall, and the parapet cap belongs to the same job rather than to a separate masonry visit.

Storms can open a surfacing quickly. After a blow, check the gravel at the low edge and around the drains, because debris carried by wind collects there. Tropical Storm Isaias in August 2020 left trees down across Baltimore and nearby counties, and a blocked outlet is quick to clear when it is found early.

Related

Flat Roof Repair

Seams, drains and membrane laps are checked, then the failed area is rebuilt so water leaves the roof.

Rowhouse Roof Replacement

The parapet, the party walls and the flat deck are read first, then the roof is rebuilt in sections.

EPDM and TPO Membrane Roofing

Seams are tested, edges are terminated, and failed membrane is patched or re-laid so the sheet holds in wind and rain.

Leak Diagnosis and Flashing Repair

The water path is traced from the ceiling back to the joint, and the flashing at that joint is rebuilt rather than sealed over.

Guides

Read before you book

FAQ

Built-Up and Modified Bitumen Roofing FAQs

Why does my built-up roof have gravel piled at the low edge?

Gravel protects the plies from sun and weather. Wind and water move loose gravel toward the low point, and the drain or edge is where it collects. Re-spreading it without fixing the drainage starts the same cycle again.

Is modified bitumen better than built-up?

Neither is better in general. Each suits different decks, edges and access. The choice depends on the existing system, the slope of the roof and how the building is used, and a roofer should explain the trade-offs for this particular roof.

Can a recoat hide a leak?

It can, if the leak is not stopped first. A coating laid over trapped moisture or a split seam seals the top while the water remains below. A recoat should follow a dry, sound layer, and the survey should show that before the coating goes on.

What is a test cut, and does it hurt the roof?

A test cut is a small opening made to read the layers. It is patched as part of the work and should not affect a sound roof. Where possible, the cut locations fall on areas that will be replaced anyway.

How do I keep a built-up roof in good condition?

Keep the drains and scuppers clear, check the surfacing after heavy storms, and have the terminations looked at on a regular schedule. A roof kept clear of debris tends to show its problems early, while they are still small and easy to correct.

Do you handle flashing at the parapet as well?

Yes. The base flashing and cap at a parapet are part of a built-up or modified scope, and they are checked along with the field. A parapet with failed metal is a frequent reason a flat section leaks at the wall, so it is never left out.

WhatsApp