Phones answered 24/7Baltimore, MD
Call (833) 751-2102
Serving Baltimore City

Finding where the water really gets in, and sealing that spot

The water path is traced from the ceiling back to the joint, and the flashing at that joint is rebuilt rather than sealed over.

  • Rowhouse flat and low-slope roofs
  • Wind and storm damage
  • Parapets, cornices and flashing

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Leak Diagnosis

Leak Diagnosis and Flashing Repair: what it covers

Quick answer

Leak diagnosis and flashing repair in Baltimore means finding the exact point where water enters a roof and sealing it with the right metal or membrane detail. Baltimore Roofing sends the call to a local roofer who follows the water path from the ceiling back up to the joint, rather than patching under the stain.

Leak Diagnosis and Flashing Repair illustration for Baltimore, MD

Most leaks are not where the stain is. Water travels along framing, down the underside of boards and across nails before it finds a route into a room. A stain on a bedroom ceiling may be fed by a joint several feet up the slope, and a patch placed directly under it leaves the real opening untouched. The diagnosis therefore starts from the stain and works upward, not from the roof surface downward.

The usual suspects change with the building. On an attached rowhouse, the junctions most worth checking are where the roof meets the parapet, the party wall or a rear addition. On a pitched house, the valleys, the chimney and the dormer cheeks take the most traffic. The same stain can have a different cause depending on which of those forms the house takes.

A diagnosis can also end with a finding that the roof is not the cause. Wall leaks, failed window seals and plumbing can all mimic a roof leak, and the roofer's job is to say so when the evidence points away from the roof. A sound diagnosis is one that says where the water is coming from, shows the reasoning, and names the repair that will stop it.

Service area
Baltimore & Baltimore City
Availability
Phones answered 24/7
Warning signs

Signs you need leak diagnosis and flashing repair

Diagnosis often involves a ladder and a roof walk, and a wet roof is slippery and dangerous. Do not stand on a suspected soft area or pull at flashing to see what is behind it. Keep the ceiling below the test area clear, and watch for dripping electrical fixtures, which should be switched off at the panel before water is run near them. Call (833) 751-2102 and say where the stain is, so the roofer can plan the access.

  • A stain that grows or moves after each new rain from a particular direction
  • Damp insulation or a soaked batt under one rafter bay only
  • Rust or dark staining on a nail tip, pipe or wire in the attic
  • A ceiling crack or bulge that softens and drips during wind-driven rain
  • Peeling paint on a wall at the top floor, with moisture behind the plaster
  • Sealant that is cracked, shrunken or lifted at a vent, chimney or dormer
  • A drip that appears only when the wind comes from one side of the house
Options

Types and options for leak diagnosis and flashing repair

Failed step flashing at a wall

Step flashing where a slope runs into a wall is one of the most common leak sources. Each step must lap over the one below and be tucked into the wall above, and where a step is missing or reversed the water runs behind the wall covering into the house.

Cracked vent boot or pipe collar

A rubber or metal collar around a vent pipe can split from sun and age, leaving a gap at the pipe. The collar is replaced with a fitted boot or a new flashing, and the pipe connection is checked for any rust or water tracking inside the wall.

Open valley or dormer cheek

Valleys carry the runoff of two slopes, and dormer cheeks take wind-driven rain from the side. Both need metal that is continuous and correctly lapped. A patch of sealant laid over an open valley seam rarely lasts through a wet winter.

Failed sealant at a joint

Sealant is sometimes the only thing holding a joint, which is a sign that the metal was not properly set. The sealant is removed, the metal is re-set, and a bead is used only where the detail allows it, never as the main barrier.

Water entering from a rear addition

Where a flat rear addition meets a taller main roof, the junction takes movement from both structures. The flashing at that junction is rebuilt with a counter-flashing set into the wall, and the drip is checked so water cannot track back under the lower roof.

One call and it gets handled.

Tell us when you need someone and we book the earliest visit a leak diagnosis and flashing repair technician has, and you approve the price before any work starts.

Tracing water back to its entry point

Water is followed along its path from the stain, through the framing, until the first place it could have been caught is found.

The stain shows where water finally dripped through, and the framing shows how it got there. A roofer begins at the stain and follows each rafter, board and nail uphill, looking for the highest point of wet or stained wood. That point is usually near the entry, though water can run a surprising distance along a board before it falls.

Once the candidate joint is identified, it is tested. The test is the proof: a controlled spray on the suspected area, watched from inside, either reproduces the leak or it does not. A leak that does not reproduce is treated as unresolved, not as fixed.

Flashing that has failed at a junction

Most roof leaks sit at a junction, where the roof meets a wall, a chimney, a vent or another roof, not in the middle of a sound field.

A junction has to shed water across a change in direction and a change in material. Metal that is overlapped the wrong way, nailed through its face or left open at a corner will let water through even when the surface around it is sound. The repair is to rebuild the detail so each piece lays over the one below it.

Sealant at a junction is a holding measure. It can slow the leak for a season, but it cannot correct metal that was set the wrong way, and it tends to split as the materials move. A lasting repair replaces the metal and keeps the sealant to the top edge where it belongs.

  • Step flashing reversed or missing at a wall
  • Vent collars split and not replaced
  • Valley metal with an open seam or a wrong lap
  • Chimney apron lifted from the surface

When the leak is not the roof

A roofer can tell a roof leak from a wall leak by its path, and should say so when the evidence points elsewhere.

Water from a wall, a window or a plumbing run can look exactly like a roof leak on a ceiling. The difference lies in the path: a roof leak tends to follow the framing from above and is worst in driving rain, while a wall leak follows the wall face and is worst when the wind hits a particular side of the house.

If the evidence points away from the roof, the roofer says so plainly and explains why. The homeowner then knows where the water is probably coming from, and the wall, window or fixture can be looked at by whoever is suited to it, rather than being patched at the roof.

Sealant, metal and the lasting fix

A lasting fix is built in metal and membrane, with sealant used only at the edges where the detail calls for it.

Each repair should answer three questions: what is the water path, what was the cause and what has been done to stop it. A patch that answers none of these will fail in the same place. A repair that answers all three is written down and tested before the roofer leaves.

The lasting fix is a joint that sheds water by design. That means metal laid with a correct lap, sealed only where sealing is intended, and checked with water. The homeowner should be shown the test and given the record of it.

Our process

How our leak diagnosis and flashing repair visit works

  1. Take the leak history in detail

    The roofer asks when the stain first appeared, which rains bring it on, and whether anything was changed nearby, such as a new vent, a fresh wall repair or a new satellite mount. The history narrows the search before anyone climbs a ladder.

  2. Trace the water upward from the stain

    From the attic or the top-floor ceiling space, the framing above the stain is followed uphill. Staining on the boards, tracks along the rafters and wet insulation all show the route. The highest point of the trail is the working hypothesis for the entry point.

  3. Test the suspected joint with a controlled spray

    A hose is run gently over the suspected area from below the joint upward, one section at a time, while someone watches from inside. The test confirms or rules out each candidate, which is quicker and more reliable than guessing from the roof surface.

  4. Rebuild the joint in the right order

    The failed flashing is lifted, the sound surface beneath it is prepared, and the new metal is set so each piece laps over the one below. Sealant is kept to the places where it is meant to be, and the joint is tested again before the roofer closes up.

  5. Record the cause and the repair

    A short written record names the entry point, the cause, the repair made and the date of the test. The record is given to the homeowner, so that the next leak is compared with this one instead of being diagnosed from scratch.

Baltimore City

Why leak diagnosis and flashing repair is different in Central Maryland

Baltimore is an independent city, in no county. A repair to a roof inside the city line falls under Baltimore City Code, Building Code Article II section 105, which requires a permit before a structure is repaired or altered. Permit amounts and inspection steps are not covered here.

Towson and Catonsville are in Baltimore County, outside the city line, and the city code does not reach them. A leak diagnosis at a county address follows the county's own rules, which this page does not set out.

A leak at the parapet or party wall of an attached house is treated with the front of the building in mind. The city's preservation staff document the front cornice before it is replaced, and a flashing repair at the front edge should be recorded with the same care.

Related

Roof Repair

The leak is traced to its source and only the failed section is rebuilt, not the whole covering.

Parapet and Party Wall Flashing

Counter-flashing is set into the mortar, caps overhang both faces of the wall, and the joint is tested before the crew leaves.

Chimney Flashing Repair

The masonry is checked first, then the metal is renewed and set into the brick so water runs off the stack.

Roof Inspection Report

The roof and the attic are checked, and a plain-language report sorts each finding by how soon it needs attention.

Guides

Read before you book

FAQ

Leak Diagnosis and Flashing Repair FAQs

Why is the stain on my ceiling so far from where the leak seems to be?

Water runs along rafters, boards and nails before it drops, so the stain marks where the water finally came through the ceiling. The entry is usually uphill of the stain, and the framing shows the route.

Can a leak be fixed with sealant?

Sealant can slow a leak for a while, but it does not correct metal that was set the wrong way. A lasting fix rebuilds the flashing so that sealant is only a secondary seal, not the main barrier.

How do I know the diagnosis is right?

The test is the proof. A controlled spray on the suspected joint, watched from inside, should reproduce the leak. If it does not, the joint is not yet confirmed, and the roofer should say so rather than close it up.

My leak only happens in wind-driven rain. Is that a roof problem?

Often it is. Wind drives water under edges and into joints that stay dry in gentle rain. The leak may still be a roof leak, or it may come from a wall or window, which is why the test is run with the wind direction in mind.

Should I wait for the next rain to see where the water comes from?

Watching the next rain is useful, but it should not replace a test. Take photographs of the stain and of the attic, note the date and the weather, and have the roofer test the suspected area while the stain is fresh.

WhatsApp