Phones answered 24/7Baltimore, MD
Call (833) 751-2102
Serving Baltimore City

Sealing the parapet and the party wall where they meet the roof

Counter-flashing is set into the mortar, caps overhang both faces of the wall, and the joint is tested before the crew leaves.

  • Rowhouse flat and low-slope roofs
  • Wind and storm damage
  • Parapets, cornices and flashing

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Parapet Flashing

Parapet and Party Wall Flashing: what it covers

Quick answer

Parapet and party wall flashing in Baltimore means sealing the joints where a roof meets a masonry parapet, a shared wall between attached houses, or the cap that runs along the top of a wall. The work is counter-flashing set into the mortar, a cap or coping that drains outward, and a drip at the outer edge. Baltimore Roofing sends it to a local roofer who records the masonry before opening any joint.

Parapet and Party Wall Flashing illustration for Baltimore, MD

On an attached rowhouse, the roof is only part of the building's weather barrier. The parapet, the party wall and the front cornice all meet the roof along lines where water can find a way past the membrane. Those lines carry movement from the masonry, the slow action of weather on mortar, and flashing that was set decades ago by someone else. When they fail, the leak appears on a top-floor ceiling well away from the joint that caused it.

Attached houses share their party walls, so a joint on that line is worked from one house but affects the wall the neighbor relies on. The city's Commission for Historical and Architectural Preservation has recorded that the front cornice of an attached row is a character-defining feature, which means the front of the parapet is often looked at more closely than the back. A roofer who understands both the joint and the street is the one to ask.

Flashing on these lines is a repair of detail more than of area. A few feet of new counter-flashing, a re-set cap and a correct drip can stop a leak that a whole new surface would not touch. The limit is the masonry itself. Where the wall is cracked or the mortar has gone, the flashing is only as sound as the brick it is set into, and the leak diagnosis page covers how that is traced.

Service area
Baltimore & Baltimore City
Availability
Phones answered 24/7
Warning signs

Signs you need parapet and party wall flashing

Parapet work happens at the edge of a roof, where a fall is serious. Keep guards or a secure line in place, do not lean over an unprotected parapet, and keep the sidewalk below clear of falling mortar. Loose brick should be left alone and reported, not pulled free by hand. Water testing is done from the roof side with a secure footing. Call (833) 751-2102 for any joint you cannot reach safely from a ladder.

  • Water staining on the top-floor ceiling along the wall that shares the roof
  • Mortar cracked or missing directly beneath a cap or at the flashing line
  • Metal lifting out of its joint, or a visible gap between flashing and brick
  • Efflorescence, a white crust, on the inside face of a parapet wall
  • A cap that has rocked loose, or one that drains back toward the wall
  • Damp patches on the attic side of a party wall after driving rain
Job stories

Typical jobs for parapet and party wall flashing

Typical job
Illustration: A typical valley-style leak at a rowhouse parapet in Baltimore

A typical valley-style leak at a rowhouse parapet in Baltimore

What homeowners notice
A stain appears on a top-floor ceiling several feet from the party wall, and it has grown after each of the last two heavy rains. The roof surface looks undisturbed from the street, and the owner cannot tell whether the water came from the roof or the wall.
What we do
The roofer starts in the attic and follows the darkened framing toward the party wall, then checks the flashing at the parapet on the same side. The flashing has lifted at one turn, and the cap above it has a crack. The flashing is relaid and the cap is re-bedded, and the wall is left to dry before any further work is planned.
What to expect
The findings record the stain, the wet framing in the attic bay and the lifted flashing, with photographs before and after. The owner is shown the route the water had been taking, and the next rain is noted as the check on the repair.

Options

Types and options for parapet and party wall flashing

Counter-flashing replacement

Failed counter-flashing is removed from its reglet and replaced with new metal of matching width. The new piece is set deeper into the mortar than the old one, so it holds through the movement of the wall and sheds water down over the base flashing below.

Parapet cap and coping rebuild

A cracked or displaced cap is lifted, the top course of masonry is re-set where needed, and a new cap is fitted with a proper overhang. Where the coping is metal, the joints are soldered or sealed and the drip is remade so it clears the face of the wall.

Party wall step flashing

Where a roof slope runs into a party wall, step flashing is woven between each shingle or membrane course and set into the wall above. Each piece is lapped over the one below so water runs downhill on top of the metal, never behind it.

Repointing at the flashing line

Mortar that has failed along the flashing line is raked out and repointed with a mortar matched in color and hardness to the surrounding brick. Soft new mortar on a hard old wall can crack the brick at the edges, so the match matters as much as the joint.

One call and it gets handled.

Tell us when you need someone and we book the earliest visit a parapet and party wall flashing technician has, and you approve the price before any work starts.

Why the joint leaks at the wall

Flashing fails at the wall because the masonry moves, the sealant ages and the metal was never set into a proper channel.

Brick and mortar expand, contract and settle at different rates, and a joint between roof and wall must follow that movement without tearing. Sealant laid over the surface of the flashing cannot do that for long. It cracks at the edges, pulls off the metal and leaves a path for water that runs straight down the inside of the wall.

The metal itself often fails at its top edge. Flashing that was fixed with nails into the mortar, or simply tucked into a joint without being cut into a channel, will lift when the wall moves. The water then gets behind the base flashing and runs along the framing until it finds a route into the room below.

Counter-flashing and the reglet

Counter-flashing sheds water down over the base flashing, and the way it is set into the wall decides how long it lasts.

Counter-flashing is the outer metal that covers the top edge of the base flashing. It has to be set into a reglet, a narrow channel cut into the mortar, so that it is held firmly and so that the edge is covered from above. A reglet that is too shallow lets the metal pull out; one that is too deep weakens the brick around it.

A good counter-flashing is bent over the base with a clear overlap and sealed only at its top edge, not across its full face. That leaves room for the metal to move and keeps water from being trapped between the two layers, which is the usual reason sealed-faced details fail early.

  • A reglet cut deep enough to hold the metal under movement
  • Counter-flashing bent over the base with a clear overlap
  • Sealant only at the top edge, never across the full face
  • Metal of a gauge matched to the length of the run

Caps, coping and the drip

The cap is the top of the wall, and its overhang and drip are what keep water off the face of the masonry.

A cap that is level or slopes back toward the wall holds water on top of the parapet, where it soaks into the brick and freezes and thaws through the winter. A cap that slopes outward and overhangs both faces sheds the water clear, and a drip cut or formed on its underside stops the water from running back along the face.

Coping can be stone, precast, or metal, and each has its own joints that need sealing at the ends and at any seam. The roofer checks each joint, because a single open joint can carry water a long way into a wall before the stain shows on the inside.

Testing the joint before closing it

A joint is tested with water, not with a look, because a flashing that looks sound can still pass water along the metal.

Water is run from a hose on the roof side, starting below the joint and working up so each section is wetted in turn. The person checking stands inside the attic or the top-floor room and watches the framing and the wall face while the water runs. A joint that passes the test is one the homeowner has watched pass.

If water appears, the source is found before the joint is closed. The roofer does not assume the leak is where the stain is; the test shows where the water actually crossed the line, and that point is the one that is repaired and tested again.

Our process

How our parapet and party wall flashing visit works

  1. Record the masonry before opening anything

    The parapet and the party wall are photographed from the roof and from the street. Cracks, loose brick, failed mortar and any existing metal are marked and measured, so the front of the building is documented before the first joint is cut.

  2. Plan the work from the house's own side

    The roofer identifies which joints fall on the shared line and which sit wholly on the house. Work on the shared line is planned so the neighbor's wall is not left open, and the neighbor is told which days the joint will be exposed.

  3. Cut the reglet and set the counter-flashing

    A narrow channel is cut into the mortar joint above the base flashing, cleaned and prepared. The new metal is set into the channel, bent down over the base, and sealed at its top edge with a sound mortar or a compatible sealant.

  4. Set the cap so it drains outward

    The cap or coping is fitted so it overhangs both faces of the wall by a measured amount and slopes outward. A drip at the outer edge stops water running back down the face of the masonry, which is where much of the staining comes from.

  5. Test with water and record the joint

    Each joint is wetted with a hose from the roof side and checked from the attic or top-floor room while the water runs. The findings and a sketch of the flashing detail go into the record the homeowner keeps.

Baltimore City

Why parapet and party wall flashing is different in Central Maryland

Baltimore City requires a permit before a structure is repaired or altered, under Baltimore City Code, Building Code Article II section 105. A party wall or parapet repair is part of that structure, so the permit question should be settled before the cap or the mortar is opened.

Historic districts and landmarks carry separate triggers under the city's preservation rules. The front cornice of an attached rowhouse is documented before it is replaced, and a parapet cap at the front of a row is treated with the same care.

Attached houses share walls, and a joint on the shared line can be worked from one side only. Telling the neighbor before the joint is exposed prevents a dispute and leaves the wall in better condition for both houses.

Related

Flat Roof Repair

Seams, drains and membrane laps are checked, then the failed area is rebuilt so water leaves the roof.

Rowhouse Roof Replacement

The parapet, the party walls and the flat deck are read first, then the roof is rebuilt in sections.

Leak Diagnosis and Flashing Repair

The water path is traced from the ceiling back to the joint, and the flashing at that joint is rebuilt rather than sealed over.

Chimney Flashing Repair

The masonry is checked first, then the metal is renewed and set into the brick so water runs off the stack.

Guides

Read before you book

FAQ

Parapet and Party Wall Flashing FAQs

Why does the leak show up inside when the flashing looks fine from the street?

Flashing that looks sound from the street can still be open at its top edge or behind its face. Water runs along the back of the metal and along the framing before it reaches the ceiling, so the stain is always some distance from the joint that let it in.

Can the parapet be repaired without the neighbor's consent?

The roofer should work from the house's own side wherever that is possible and tell the neighbor before any part of the shared line is opened. Whether a formal agreement is needed depends on the work, and the roofer can say what applies to the joint in question.

Is sealant enough to stop a parapet leak?

Sealant can hold a joint for a while, but it is not a substitute for properly set metal. A repair that relies on sealant alone tends to return at the same spot, so a sound joint is built with counter-flashing in a reglet and the sealant kept to the top edge.

How do I know the cap is draining outward?

Watch the cap in rain from a safe position, or ask the roofer to show the slope and the drip before the work is closed up. Water that runs back toward the wall face is the sign of a cap that needs re-setting.

What if the brick itself is cracked?

Cracked brick is a masonry problem as well as a flashing one. Once the cracks are recorded, the roofer says whether the flashing can be set into sound brick or whether the masonry must be repaired first. The sequence matters, because metal fixed into a cracked wall will move with it.

Does the work need a permit?

In Baltimore City, a permit is required before a structure is repaired or altered under the building code. Ask the roofer to confirm who pulls it. Permit amounts and inspection steps are not covered on this page.

WhatsApp