Phones answered 24/7Baltimore, MD
Call (833) 751-2102
Serving Baltimore City

Single-ply membrane roofs for low-slope buildings in Baltimore

Seams are tested, edges are terminated, and failed membrane is patched or re-laid so the sheet holds in wind and rain.

  • Rowhouse flat and low-slope roofs
  • Wind and storm damage
  • Parapets, cornices and flashing

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

EPDM and TPO

EPDM and TPO Membrane Roofing: what it covers

Quick answer

EPDM and TPO membrane roofing in Baltimore is single-ply work: a large sheet of synthetic membrane laid over a low-slope deck, with its seams bonded or welded and its edges fixed with metal. Baltimore Roofing routes repair and replacement of these roofs to a local roofer who tests the seams before the membrane is trusted.

EPDM and TPO Membrane Roofing illustration for Baltimore, MD

Single-ply membrane is one of the common low-slope systems for flat roofs. EPDM is a rubber-based sheet, usually black, and TPO is a thermoplastic sheet, often white or light gray. Both are laid as one layer rather than built up in plies, so their seams are where their performance is decided. A membrane that is sound across the field can still leak at a seam or an edge that was never properly sealed.

Where a low-slope rowhouse roof in the city has failed, a single membrane sheet is one of the replacement options considered, provided the deck beneath is sound and the drainage can carry the water. The attached-house form, with its parapet or front cornice, sets limits on where the membrane can run up the wall and how the edge is fixed.

Membrane work is precise work. A seam bonded in cool, damp conditions may open later, and an edge that was taped rather than properly terminated will lift in wind. A roofer checks the seams and the terminations as carefully as the field, because those details decide how long the membrane holds.

Service area
Baltimore & Baltimore City
Availability
Phones answered 24/7
Warning signs

Signs you need epdm and tpo membrane roofing

Membrane surfaces can be slippery when wet, and some repair adhesives and solvents need ventilation. Keep open flames and hot-air welders away from combustible material, stay back from edges and skylight openings, and do not walk a membrane that is wet, frozen or blistered. Report any leak or sagging deck to (833) 751-2102 and let a roofer make the call on access.

  • Seams that lift, peel or show a gap at the lap
  • Membrane pulled away from a wall, a curb or a drain
  • Cracks or splits in the sheet that widen after cold weather
  • Ponding that persists after the outlets have been cleared
  • Edge metal loose or missing along a parapet or a roof edge
  • Ceiling staining that appears where a seam crosses a joist
Options

Types and options for epdm and tpo membrane roofing

EPDM sheet repair

EPDM is commonly repaired with a patch of matching sheet, bonded to the cleaned membrane with an approved adhesive and lapped well past the damage. A failed seam may be re-bonded in the same way once the surface has been cleaned and primed.

TPO seam and sheet repair

TPO repairs are usually heat-welded. A new piece of TPO is set over the failed area and welded at its edges to the sound membrane, and the weld is probed afterward to confirm it has fused across its full width.

Edge and parapet termination

A membrane is finished at an edge or a parapet by taking it up the wall, fixing it under a metal cap or termination bar, and sealing it at the top. The detail is repeated at each wall so that wind and water cannot reach beneath the sheet.

Drain and penetration detail

A drain, pipe or equipment support is flashed with a fitted boot or a sealed flange, and the membrane is clamped or bonded to it. The repair is small, but a penetration is a common point for water to enter, so it deserves the same care as the field.

Full membrane replacement

When the sheet is failing across a broad area, it is removed or overlaid, and a new sheet is laid with new seams, edges and drain rings. This is the option that deals with brittleness, widespread seam failure and a deck that has been wet for too long.

Skip the guesswork. Call for a straight answer.

Tell us what's happening and we'll tell you honestly whether it's a quick fix, and what epdm and tpo membrane roofing should cost.

Seams are the working part of a membrane roof

Each seam is a joint the roof depends on, and its condition is tested rather than assumed from the surface.

EPDM seams are typically joined with a seam adhesive or tape, and TPO seams are typically welded with heat. Whichever method was used, a seam is sound only when the two sheets are fully bonded across their width. A roofer probes the seam with a tool and looks for any section that lifts or shows a gap, because a seam that looks closed from above can be open underneath.

When a seam fails, the repair is either re-bonding the open section with an approved adhesive or weld, or laying a strip of matching membrane over the seam with a generous overlap. Dust, moisture and temperature control the bond, so repairs are timed to the conditions on the day and the surface is cleaned first.

Edges, terminations and drains

Membrane is fixed at its edges and at each drain, and those fixings resist wind as much as the field does.

The edge of a membrane roof is where wind does its work. A membrane that is simply glued or taped at the edge can lift in a gust, and once a corner lifts, the wind gets underneath. Edge metal is fixed to the deck and the membrane is terminated into it, so the whole system is held down along its perimeter.

Drains need a clamping ring that holds the membrane firmly to the outlet body, with a seal between them. A drain set with the membrane loose around it tends to pull free over time and let water track beneath the sheet, so the drain is one of the first points checked in any repair.

  • Metal edge set and fastened into the deck
  • Membrane terminated and sealed at the top of each wall
  • Drain clamping rings bolted down and sealed
  • Penetrations flashed with fitted boots or sealed flanges

Membrane or built-up: which fits the deck?

A single membrane suits a deck that can take one sheet with careful seams, while built-up systems suit decks that need plies built in place.

A single-ply sheet works best over a clean, dry and smooth deck, and its seams need access and controlled conditions to be bonded properly. A built-up roof is assembled in place from plies and copes more easily with some irregularity in the deck. Neither is better in every case, and a reading of the existing roof decides the choice.

Membrane is sometimes laid over an existing surface when the drainage and the deck allow it. The roofer checks the substrate, removes loose material and confirms the surface is sound before any new sheet goes down, because a membrane is only as flat and clean as the surface it sits on.

Keeping a membrane roof trustworthy

Regular checks of seams, edges and drains catch small failures while they are still easy to repair.

A membrane roof rewards a simple routine. Drains are cleared of leaves, grit and debris, the edges are looked at after storms, and any new blister, crack or lifted seam is noted with a date. A written record of what was seen and where is more useful than a repair made after water has reached the ceiling.

Foot traffic is another factor. Membrane is damaged by dropped tools, sharp debris and equipment dragged across the surface. Walkways or pads at access points and beside rooftop units keep the membrane from being struck repeatedly in the same places.

Our process

How our epdm and tpo membrane roofing visit works

  1. Survey the field and the seams

    The membrane is walked with care and the seams are probed. Blisters, cracks, punctures and lifted laps are marked on a plan of the roof, together with the position of each drain and penetration.

  2. Clean and prepare the surface

    Dust, grit and moisture are removed from the repair area, since bonding fails on a dirty or wet surface. The drains are cleared, and the membrane around the repair is checked for adhesion before any patch is set.

  3. Set the patch or the new sheet

    Repair patches are cut with rounded corners and bonded or welded to the sound membrane with a generous margin. Full replacement sheets are positioned, aligned and seamed with the edges kept square to the wall they climb.

  4. Test the seams and the drains

    Each new seam is probed, and the drains are tested with water. Edge metal and terminations are checked again, and the roofer records what was repaired and where, so the next visit starts from a known position.

Baltimore City

Why epdm and tpo membrane roofing is different in Central Maryland

Baltimore is an independent city, in no county, and a membrane roof where a structure is repaired or altered falls under Baltimore City Code, Building Code Article II section 105. A membrane replacement is covered by that rule, so the roofer should confirm the permit before work begins. Permit amounts are not covered on this page.

Where a membrane meets a parapet or a front cornice, the detail is governed by the edge of the building as well as the roof. The city's preservation staff treat a front cornice as a character-defining feature, so a membrane termination near the front of a rowhouse is scoped with that in mind.

Related

Flat Roof Repair

Seams, drains and membrane laps are checked, then the failed area is rebuilt so water leaves the roof.

Parapet and Party Wall Flashing

Counter-flashing is set into the mortar, caps overhang both faces of the wall, and the joint is tested before the crew leaves.

Roof Replacement

The deck, the drainage and the flashing are read first, and the scope is written before any covering comes off.

Guides

Read before you book

FAQ

EPDM and TPO Membrane Roofing FAQs

Does a membrane seam need replacing when it looks closed?

Sometimes. A seam can look closed from above while the bond beneath has failed. Probing is the test, and a seam that moves or gives under the tool is re-bonded, whatever it looks like from the ground.

Can a membrane roof be walked on?

It can be walked with care in dry weather, by people trained to work on it. Heavy or repeated traffic should be routed along walkways or pads, so the membrane is not dragged or punctured in the same places.

Is EPDM or TPO the better choice?

Neither is better in general. The deck, the seams the crew can make on the day, the exposure and the way the roof is used all bear on the decision. A roofer should explain why one suits this building.

What causes a membrane to lift at the edge?

Wind finds a corner or a loose edge where the membrane is not properly terminated. Once the edge lifts, the wind gets under the sheet and the lift spreads. The fix is to re-fix the metal and the membrane at the edge, not to tape over it.

What should I receive after a membrane repair?

A written record of the repaired areas, a plan showing the position of each patch or seam, the materials used, and any warranty the installer provides in writing. Keep the record with the house papers for the next job.

WhatsApp