Phones answered 24/7Baltimore, MD
Call (833) 751-2102
Serving Baltimore City

Replacing a skylight, its curb and its flashing in Baltimore

The old unit is lifted, the curb and flashing are rebuilt to suit the roof, and the new skylight is set and water-tested.

  • Rowhouse flat and low-slope roofs
  • Wind and storm damage
  • Parapets, cornices and flashing

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Skylight Replacement

Skylight Replacement: what it covers

Quick answer

Skylight replacement in Baltimore means removing a failed skylight or roof window and fitting a new unit, with its curb, flashing and glazing reset to suit the roof around it. Most skylight leaks begin at the flashing rather than the glass. Baltimore Roofing sends the work to a local roofer who checks the curb and the deck before the old unit is lifted.

Skylight Replacement illustration for Baltimore, MD

A skylight is a window set into the roof, and it inherits the roof's weather problems along its whole perimeter. The glass may be perfectly sound while the flashing around it has lifted, the curb has rotted or the sealant has split. Replacing only the glass in those cases leaves the cause of the leak in place, which is why a skylight job starts with the frame and the flashing rather than the unit itself.

On a flat or low-slope section, a skylight sits within the membrane or built-up field, and its curb is part of the same waterproofing as the surrounding roof. On a pitched roof, the curb is framed into the rafters and the upslope flashing is the detail that carries most of the load. Either way, the roofer reads the surrounding covering before deciding how the new unit is set into it.

Replacement also corrects the opening. A skylight set too low on a slope, or fitted without a proper curb and upslope apron, will leak whatever unit is placed in it. A good scope names the opening, its size and its slope, and says what will change so that the new unit sheds water as the designer intended.

Service area
Baltimore & Baltimore City
Availability
Phones answered 24/7
Warning signs

Signs you need skylight replacement

A skylight opening is a fall hazard, both while the old unit is removed and after the opening is left uncovered. Cover any open skylight with a secure panel before leaving the roof, mark the opening clearly, and do not step on the glazing of an older unit, which can break without warning. Keep the room below clear of falling glass during removal, and call (833) 751-2102 before any work that changes the opening itself.

  • A ring of staining on the ceiling around the skylight, darkest at the top edge
  • Water that runs down the inside of the glass frame during rain
  • Sealant that is cracked, shrunken or pulling off the flashing lip
  • Drips from a skylight that only appear when the wind drives rain uphill
  • Fogging or moisture between the panes of an insulated unit
  • Rot or softness in the curb wood visible from inside the attic
Options

Types and options for skylight replacement

Fixed skylight replacement

A fixed unit is the simplest to set and the most common replacement. It is sealed to its curb and flashed around its perimeter, and the glazing is chosen for light, insulation and the rooms beneath, with the choice recorded in the scope.

Operable roof window replacement

An operable roof window opens for ventilation, and its hinges and seals add moving parts that must stay watertight. The replacement is set with a flashing kit that accepts the opening motion, and the operating hardware is checked for smooth travel.

Curb rebuild around an old opening

When the curb has rotted or was never built properly, the opening is rebuilt around a new frame. The old wood is cut back to sound timber, the framing is repaired, and the new curb is flashed as a single unit with the surrounding roof.

Skip the guesswork. Call for a straight answer.

Tell us what's happening and we'll tell you honestly whether it's a quick fix, and what skylight replacement should cost.

Condensation or a leak: telling them apart

Water on the inside of a skylight can come from humid air condensing on a cold surface, or from water entering the frame, and the two need different fixes.

Condensation tends to appear on cold mornings, forms across the glass rather than in a line, and clears as the room warms. A leak tends to appear during rain, follows a path along the frame or the flashing, and does not depend on the temperature of the room. The first can often be reduced by ventilation and humidity control, while the second needs the roof fixed.

The distinction is worth making before any work begins, because a skylight replaced to stop condensation will still leak if the flashing is the cause. The roofer records the pattern of the moisture, the weather when it appears and the place it first shows, and uses those notes to decide the scope.

The curb and the flashing

The curb holds the unit and the flashing keeps water out of the joint, and both have to be right for the unit to perform.

The curb is the upstand the unit sits on, and it is usually framed from the same rafters and headers as the opening. Its wood must be sound and its corners must be tight, because movement at a corner opens a route for water into the framing. Where the curb is damaged, it is rebuilt before the unit goes back in.

The flashing around a skylight is made of several pieces. The upslope piece is the most important, because it carries water over the top of the unit. The head piece and the side pieces lap over the courses of the roof, and the sill piece sheds water downhill. Each has to be set in order, so the water always runs over the metal and never under it.

  • Curb wood sound, tight at each corner and free of rot
  • Upslope flashing set beneath the courses above it
  • Side flashing lapped over the roof courses at each edge
  • Sill flashing sending water clear of the lower curb

Choosing the unit and its glazing

The unit is chosen for light, insulation and how the room will be used, and its glazing is matched to the climate of the space it lights.

A skylight's glazing affects how much heat it lets through, how much light reaches the room and how much noise and condensation it produces. Insulated units with multiple panes reduce heat loss and condensation at the glass, and a tinted or coated pane can cut glare. The choice should be made with the room beneath in mind rather than from the catalog alone.

The unit's size, its slope and the framing around it are part of the same decision. A larger unit needs stronger framing, and a unit set too low on the slope sheds water less efficiently. The roofer checks each of these against the opening and recommends a size the curb can support.

Framing changes and the opening

A new skylight is sometimes a chance to change the opening, and any change to the framing has to be scoped and checked.

Enlarging or moving an opening means cutting rafters and fitting new headers, which alters the structure of the roof and counts as altering the building. In Baltimore City that work falls under the city's permit requirement, and the roofer should confirm the permit before any rafter is cut.

Where the opening stays the same size, the framing is checked and repaired but not changed. That is the simpler job, and it is usually the right one when the existing position is sound and the only problem is the unit and its flashing.

Installing and testing the new unit

The new skylight is set, secured and water-tested before anyone signs off the job, because the test is the only real proof of the flashing.

Once the flashing is in place, the unit is lowered onto its curb, shimmed level and fixed to the framing with the fixings the manufacturer specifies. The interior trim and any insulation around the frame are then finished, and the glazing is checked for seals and for any scratches from fitting.

The water test is run after the unit is secured and before the surrounding covering is finished. The homeowner should watch it, because a joint that passes a test is one that has been seen to pass.

Our process

How our skylight replacement visit works

  1. Tell a leak from condensation

    Moisture on the inside of a skylight can be condensation, which is a ventilation and humidity matter, or a leak, which is water entering at the frame. The roofer checks the timing, the location of the wet area and the state of the flashing, and writes down which it is before any work is planned.

  2. Check the curb and the deck from below

    The attic side of the opening is examined for soft curb wood, staining on the framing and any rusted fixings. Where the deck is sound the new unit can be set into it, and where it is not the decking is repaired before the curb is rebuilt.

  3. Lift the old unit and the failed flashing

    The old skylight is removed with care, and its flashing is lifted along each edge. The surrounding covering is cut back to a clean line, so the new flashing can lap properly over the courses above and under the sides.

  4. Set the new curb and flashing in order

    The flashing goes in from the bottom up and the top down, so each piece laps over the one below it. The new unit is then set on its curb and secured, and the joints are sealed only where the detail allows a bead.

  5. Water-test the opening before closing

    A hose is run over the skylight from above while a second person watches the inside and the attic. The test runs long enough to wet the upslope flashing and the head, since those are the joints that most often pass water in a real storm.

Baltimore City

Why skylight replacement is different in Central Maryland

Baltimore City requires a permit before a structure is repaired or altered, under Baltimore City Code, Building Code Article II section 105. Enlarging a skylight opening or cutting new framing counts as altering the structure, so the permit question should be answered before the opening is changed.

A skylight on the front slope of a rowhouse, or one that can be seen from the street in a historic district, may need review under the city's preservation rules. The front cornice of an attached house is treated as a character-defining feature, so a new opening on that face is planned with that in mind.

Skylights on the flat rear roofs of attached houses sit inside a membrane or built-up field. The curb is then part of that surface, and the roofer should confirm which surface system the new unit ties into before the curb is built.

Related

Flat Roof Repair

Seams, drains and membrane laps are checked, then the failed area is rebuilt so water leaves the roof.

Leak Diagnosis and Flashing Repair

The water path is traced from the ceiling back to the joint, and the flashing at that joint is rebuilt rather than sealed over.

Roof Maintenance Plan

Seasonal checks, drain clearing and post-storm visits are set to the house, and the findings are kept in one record.

FAQ

Skylight Replacement FAQs

Why does my skylight leak only when it rains hard?

Driving rain can push water up under the upslope flashing or past a worn sealant line, which gentle rain does not do. The leak often points to a weakness in the flashing rather than in the glass, and the test shows where the water crosses.

Can I replace just the glass in a skylight?

Sometimes, if the frame and the flashing are sound and the glazing alone has failed. Where the leak comes from the curb or the flashing, a new glass unit will not stop it, so the roofer checks the joints first.

Will a new skylight reduce condensation?

A better glazing unit can reduce condensation on the glass, but humid air in the room is often the larger cause. Ventilation and humidity control are part of the advice, and the roofer should say so if the moisture is not from a leak.

How do I choose the right size?

The size is set by the opening, the framing and the light the room needs. A larger unit needs stronger framing, so the roofer checks the curb before recommending a size. A unit in the wrong place is hard to fix later, so the position is part of the decision too.

Does a skylight replacement need a permit?

Replacing a unit in its existing opening may not change the structure, but enlarging the opening or cutting new framing does. In Baltimore City, ask the roofer to confirm whether the job falls under the permit requirement before any rafter is touched.

How long should a new skylight seal last?

Sealant and flashing age with sun and temperature, so they need checking on a regular basis rather than being assumed to last. A roofer can show the sealant lines at each visit and say when a joint is due attention.

WhatsApp