Phones answered 24/7Baltimore, MD
Call (833) 751-2102
Serving Baltimore City

Chimney flashing, and the brick it is set into, in Baltimore

The masonry is checked first, then the metal is renewed and set into the brick so water runs off the stack.

  • Rowhouse flat and low-slope roofs
  • Wind and storm damage
  • Parapets, cornices and flashing

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Chimney Flashing

Chimney Flashing Repair: what it covers

Quick answer

Chimney flashing repair in Baltimore means renewing the metal and sealed joints where a chimney passes through a roof: the step flashing along the sides, the apron at the front, the counter-flashing set into the masonry and the crickets that shed water behind the stack. Baltimore Roofing routes the work to a local roofer who checks the brick before any metal is lifted.

Chimney Flashing Repair illustration for Baltimore, MD

A chimney is the one roof feature where three materials meet: masonry, metal and the roof covering. Each moves at its own rate, and the joints between them are where the water finds its way. Chimney flashing is therefore one of the more frequent sources of roof leaks, and a repair that ignores the brick around the metal will return within a few seasons.

Masonry chimneys are a feature of many older houses, and older stock often carries a chimney that has been repointed, rebuilt or capped more than once. Each of those changes leaves a different joint behind. A roofer working on a rowhouse or a pitched house will read the chimney first, because the flashing is set into it and cannot be understood without it.

The good news is that chimney flashing is well understood. The metal can be renewed, the counter-flashing reset into fresh mortar, and the crickets rebuilt where water collects behind the stack. The job is precise rather than large, and the difference between a lasting repair and a temporary one is usually the care taken with the joint at the brick.

Service area
Baltimore & Baltimore City
Availability
Phones answered 24/7
Warning signs

Signs you need chimney flashing repair

A chimney is heavy, and loose brick or a cracked cap can fall. Keep the area below clear, do not lean on the stack for balance, and do not climb a ladder that rests on the chimney itself. Cold or cracked flue liners can carry smoke into the house, so tell the roofer if you smell smoke or see staining inside the flue. Call (833) 751-2102 before any masonry is removed from the top of the stack.

  • A stain on the ceiling or wall at the chimney, darkest in driving rain
  • Metal at the apron or sides lifted, bent or pulled away from the brick
  • Mortar cracked, crumbling or missing where the flashing meets the stack
  • Rust streaks running down the brick below a joint
  • Water staining in the attic along the chimney side of the roof boards
Job stories

Typical jobs for chimney flashing repair

Typical job
Illustration: A typical chimney flashing check on an older house in Arbutus

A typical chimney flashing check on an older house in Arbutus

What homeowners notice
Water shows on the wall beside a brick chimney during heavy rain. The owner has been told by someone else that the chimney needs to be rebuilt, and wants a second opinion before any work is agreed.
What we do
The roofer inspects the flashing at the chimney base and the counter-flashing set into the brick. The base flashing is sound, but the counter-flashing has a gap at one corner where the mortar has cracked. The gap is sealed and the mortar is cut back and re-pointed by a mason, with the work scheduled separately.
What to expect
The owner receives a written finding that the chimney structure was not the cause and that the leak was at the counter-flashing. The mason's part and the roofer's part are listed on separate lines of the scope, and the owner is told whether a permit applies.

Options

Types and options for chimney flashing repair

Step and apron flashing

Step flashing runs up each side of the chimney, lapped with the roof courses, and apron flashing sits across the front. Both are renewed when they fail, and the new pieces are lapped so water runs over every joint on the way down the roof.

Counter-flashing and reglet

Counter-flashing covers the top edge of the base metal and is set into a reglet cut in the brick. A reglet that has weathered loose is re-cut deeper into sound mortar, and the metal is set so it can move with the stack.

Crickets behind the stack

A cricket is a small peaked saddle built behind a chimney that is wider than the stack, so water flows around the back instead of pooling against the brick. Where a cricket is missing, one is built and tied into the covering so it sheds water cleanly.

One call and it gets handled.

Tell us when you need someone and we book the earliest visit a chimney flashing repair technician has, and you approve the price before any work starts.

Why chimneys leak more than other roof features

A chimney passes through the roof and holds several joints at once, and every one of them is a path for water.

The metal at the sides, the apron at the front and the counter-flashing in the brick each have to hold water out while the stack moves. Heat from the flue and the weather on the masonry cause expansion and shrinkage, and the joints open slightly with each cycle. Over years, a small gap becomes a route for water that runs down the brick and into the attic.

The chimney also collects water behind it. Without a cricket, rain strikes the back of the stack and runs down the upslope side of the flashing, which is one reason a leak often appears on the side of the chimney that faces the uphill roof.

The masonry has to be sound before the metal

Metal is only as sound as the brick it is set into, so the masonry is repaired first where it is failing.

Brick that has spalled, mortar that has crumbled, or a cap that has cracked will let the flashing move and let water in behind it. Repointing the joints where the flashing sets, and replacing cracked brick or a cracked cap, comes before the new metal is fitted. Skipping that step means the new flashing will fail in the same way as the old.

Where the chimney is on a building in a historic district or a landmark, masonry work may need review before any brick is removed or replaced. The roofer should identify that before the work begins, rather than after a stone has been lifted.

  • Cracked or spalled brick replaced in matching units
  • Failed mortar raked out and repointed where the flashing sets
  • A cracked cap rebuilt with a proper overhang and drip
  • Metal set into a reglet cut in sound mortar

Choosing between a repair and a rebuild of the stack

Most chimney leaks are repaired at the flashing, but a stack that is badly failed may need a rebuild above the roof line.

A repair is right when the brick is sound, the mortar is holding, and the failure is confined to the metal and its joints. It is quicker, less disruptive and usually adequate. A rebuild of the upper stack is the better choice when the brick is deteriorated through its height, when the flue liner is damaged or when the stack is no longer stable.

Whichever is chosen, the roofer should say why. A chimney that needs more than flashing is a masonry job, and the roofer should explain what that involves and who should be asked to carry it out, rather than leaving the homeowner to find out after the metal is set.

Our process

How our chimney flashing repair visit works

  1. Read the masonry from the roof and the attic

    The brick, mortar and cap are examined first, from the roof and from the attic where the chimney passes through. Cracks, spalling and failed pointing are recorded, because the metal can only be as sound as the stack it is set into.

  2. Lift the metal and check the wall behind it

    The step and apron flashing is lifted carefully, and the sheathing and underlayment beneath are checked for soft wood or staining. Any damage found is recorded and repaired before new metal is fitted, so the joint is not closed over a hidden problem.

  3. Reset the counter-flashing and rebuild the crickets

    Fresh reglets are cut into sound mortar, the counter-flashing is set and sealed at its top edge, and the cricket behind the stack is built so water is turned away from the back of the chimney. The new work is aligned with the lines of the roof.

  4. Test the stack with water and close up

    The chimney is wetted from the roof side while someone watches the attic and the ceiling below. Only when the joint passes is the covering finished around it and the work cleared away.

Baltimore City

Why chimney flashing repair is different in Central Maryland

Baltimore City requires a permit before a structure is repaired or altered, under Baltimore City Code, Building Code Article II section 105. Rebuilding the upper part of a chimney counts as altering the structure, so ask whether the permit has been pulled before the brick is removed.

A chimney on an attached rowhouse sits where the roof meets a shared wall. The flashing at that wall is part of the same joint, and the parapet or party wall detail should be checked while the chimney is open. The parapet and party wall flashing page covers that junction.

Chimneys on detached houses in Towson, Dundalk and other Baltimore County neighborhoods follow county rules rather than the city code. The roofer should confirm which requirements apply before work begins at a county address.

Related

Leak Diagnosis and Flashing Repair

The water path is traced from the ceiling back to the joint, and the flashing at that joint is rebuilt rather than sealed over.

Roof Repair

The leak is traced to its source and only the failed section is rebuilt, not the whole covering.

Shingle Roof Replacement

The old covering comes off to the deck, the boards are checked, and a new shingle system is laid over fresh underlayment.

Roof Maintenance Plan

Seasonal checks, drain clearing and post-storm visits are set to the house, and the findings are kept in one record.

Guides

Read before you book

FAQ

Chimney Flashing Repair FAQs

Why does my chimney leak only in driving rain?

Driving rain pushes water under metal and into joints that stay dry in a gentle shower. A chimney leak often shows up that way because the joints are open just enough to pass water under pressure but not enough to drip in calm weather.

Can the flashing be replaced without rebuilding the chimney?

Usually yes, if the brick and mortar are sound. Where the masonry is cracked or the mortar has failed, the repointing and any brick replacement come first, and the new metal is then set into the repaired joint.

What is a cricket, and do I need one?

A cricket is a small saddle behind a wide chimney that turns water around the stack instead of letting it pool on the upslope side. Whether one is needed depends on the chimney's width and the roof around it, and the roofer should say so in the scope.

Is the chimney cap part of the flashing job?

It can be. A cracked or missing cap lets rain into the flue and onto the top of the brick, so the cap is checked and replaced with the flashing if it is failing. The cap is part of the same water barrier.

How do I know the flashing is sealed properly?

Ask for a water test before the crew leaves. A hose run over the chimney while someone watches the attic and ceiling below shows whether the joint holds, and the roofer should record the result.

Should I use a sealant to fix a small gap?

A small gap in mortar is better repaired by repointing than by sealant laid over it. Sealant at a flashing edge is acceptable as a secondary seal, but it should not be the main barrier and should not be spread across the face of the metal.

WhatsApp