Phones answered 24/7Baltimore, MD
Call (833) 751-2102
Serving Baltimore City

Gutters, downspouts and scuppers that carry roof water away in Baltimore

Sagging runs are re-hung and re-pitched, joints are sealed, and the outlets that serve the roof are cleared and checked.

  • Rowhouse flat and low-slope roofs
  • Wind and storm damage
  • Parapets, cornices and flashing

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Gutter Repair

Gutter and Downspout Repair: what it covers

Quick answer

Gutter and downspout repair in Baltimore means restoring the channels and outlets that carry rainwater off a roof: re-hanging sagging runs, sealing joints, re-pitching gutters, reconnecting downspouts, and clearing the scuppers and outlets that serve flat roofs. Baltimore Roofing sends these calls to a local roofer who checks the roof edge where each gutter begins.

Gutter and Downspout Repair illustration for Baltimore, MD

A gutter is easy to ignore until it overflows onto a walkway or a foundation. It is part of the roof system, though, and its failures often show up as roof damage. Water that spills over a sagging run runs back under the eave, soaks the fascia and reaches the top courses of the shingles or the edge of a membrane. Gutter repair is therefore more than a job on the edge of the house.

Attached houses can drain differently from pitched ones. A flat roof behind a parapet may drain through a built-in gutter, a scupper set in the wall or a short hanging gutter at the rear, and a blocked outlet on those roofs is the same problem as a blocked gutter with the water spread across a whole flat section. The city's rowhouse form makes the outlets worth checking on every visit.

Gutter work is simple to do well, and the damage that follows neglect is far from simple to undo. A few hours of re-hanging and cleaning can save a fascia, a soffit and the top course of a roof that would otherwise be repaired at a much larger scale. The job is small, but its effect on the rest of the building is large.

Service area
Baltimore & Baltimore City
Availability
Phones answered 24/7
Warning signs

Signs you need gutter and downspout repair

Gutter work is done from a ladder, and most ladder falls happen on uneven ground or with a ladder set at the wrong angle. Set the ladder on firm, level footing, keep a second person at the base, and do not reach too far to the side. Keep electrical lines and service drops clear of the ladder. Do not work on a gutter in wet or icy weather, and call (833) 751-2102 for any run that is higher than a safe ladder can reach.

  • Water falling from the gutter in a sheet at one spot during rain
  • A gutter sagging between hangers and holding standing water
  • Fascia boards darkened or soft directly below a joint
  • Granules or grit collecting in the gutter trough
  • A downspout clogged at the elbow or pulled from its clip
  • Paint peeling on the soffit under a run that overflows
  • Water pooling at the base of a wall after every heavy rain
Options

Types and options for gutter and downspout repair

Sagging or detached gutter runs

A run that has pulled away from the fascia or sags between hangers is re-hung on sound brackets fixed into the rafters or the fascia. Where the old fixings have rusted through or pulled out, new ones are set so the run carries its water weight without moving.

Leaking joints and end caps

Joints between gutter sections and the end caps are the common leak points. The old sealant is cut out, the surfaces are cleaned and dried, and a fresh seal is laid at each joint and end, so the run holds water until it reaches the outlet.

Clogged or crushed downspouts

A downspout can clog at its elbow or be crushed by a knock from a ladder or a vehicle. The elbow is cleared or replaced, the section is re-fitted with its clip, and the outlet is checked to make sure the water leaves the foot of the building.

Flat-roof outlets and scuppers

On flat roofs, outlets and scuppers gather water from a whole section. A scupper that sits above the low point of the roof, or an outlet that has filled with debris, holds water on the roof rather than letting it leave. The outlet is cleared or re-set, and its flow is tested.

Need gutter and downspout repair today?

Call any hour and explain what is going on. You get a clear price before any work starts.

Where the water should go

Every gutter has to carry water to a point where it leaves the building, and the route should be clear from the roof edge to the ground.

The route begins at the roof edge, where the gutter collects water along the eave, and runs to the downspout that drops it to ground level. At the foot of the building, the water should be carried away from the foundation rather than allowed to pool at the wall. A break anywhere along that route sends the water somewhere it was not meant to go.

Trace the route with a hose on a dry day. Any spot where the water stops, spills or runs the wrong way marks a point that needs attention. The route is only as sound as its weakest joint, so the trace is worth doing before any part of the system is replaced.

Pitch, hangers and the fascia

A gutter holds water only when it is level or pitched correctly and fixed to a fascia that can carry its weight.

The pitch of a gutter is a small slope toward the outlet, and a run that has lost it will hold water in its low spots until the sediment builds up and overflows. Re-pitching is done by adjusting the hangers, and it has to be checked along the full length of the run, not only at the ends.

Behind the gutter, the fascia and the rafter ends take the weight and the wet. Soft or darkened fascia below a joint is a sign that water has been running over the edge for some time, and it should be opened and checked before the new gutter is hung.

  • Hangers reset to hold a consistent pitch to the outlet
  • Brackets fixed into sound rafter ends or solid fascia
  • Soft fascia cut back and replaced in matching board
  • Soffit checked where a run has been overflowing

Downspouts and the ground

A downspout that discharges at the foot of the wall is only half the job, since the water also needs to move away from the foundation.

Downspouts should be fixed to the wall at intervals that keep them straight, and their elbows should turn the water away from the building rather than into it. A discharge that falls directly against the foundation can soak the wall at its base for years, so the outlet is extended or angled where the layout allows.

At the ground, a splash block or a short extension carries the water clear of the wall. Where the outlet joins a shared alley or a neighbor's property line, the discharge should be planned so water does not cross the line, and the homeowner should decide that with the roofer before the work is set.

Outlets and scuppers on flat roofs

On a flat roof, the outlets do the work that the gutters do on a pitched house, and they need the same attention.

A scupper is an opening in a parapet or wall that lets water off a flat roof and into a downpipe or onto the ground. Its sill has to be set low enough that water can reach it across the surface, and its metal has to be lapped with the membrane so water runs out without tracking back under the roof covering.

A flat-roof outlet is a drain set into the roof surface. Its strainer is cleared regularly and its clamping ring has to hold the membrane firmly. An outlet set above the lowest point of the roof will hold water on the surface, which is why its height is checked when the drain is cleared.

Our process

How our gutter and downspout repair visit works

  1. Watch the flow in the rain

    The first step, when the weather allows, is to see where the water goes during a rain. Overflow points, leaking joints and downspouts that fail to discharge all show clearly while the rain is falling, and a note of each is the basis for the repair.

  2. Clear and check the run

    Debris is removed by hand from every section, and the trough is flushed to confirm the water flows to each outlet. Brackets and hangers are checked for rust or loose fixing, since a clean gutter on weak brackets will still sag under its own weight.

  3. Re-hang and re-pitch the run

    Sagging sections are re-hung on new or reset brackets, and the pitch is set so water runs toward the outlet without standing. A run that falls the wrong way is corrected before any joint is sealed, since a level gutter is what holds the water.

  4. Reconnect the downspouts and seal the joints

    Each downspout is reattached at its elbow and clip, and the seams and end caps are sealed with a suitable sealant. Outlets are checked to make sure the discharge is clear of the foundation and not flowing back under the eave.

  5. Test with water and leave a note

    The system is run with a hose from the high end, and each joint and outlet is watched until the water is carried away. The roofer leaves a short note of what was fixed and where, for the homeowner's records.

Baltimore City

Why gutter and downspout repair is different in Central Maryland

Gutter repair on the front of an attached rowhouse can touch the front cornice, which the city's preservation staff treat as a character-defining feature. Fixings into the cornice or the fascia at the front are recorded before they are changed.

Baltimore is an independent city, in no county. Work that repairs or alters the building's structure, such as a fascia or rafter end, can fall under Baltimore City Code, Building Code Article II section 105. Ask the roofer whether the scope calls for a permit.

Outlets matter most in heavy rain. Where a gutter overflows at a neighbor's property line, the run is redirected so the water stays on the house's own lot, and the homeowner and roofer agree on the route before the new gutter is fixed.

Related

Roof Maintenance Plan

Seasonal checks, drain clearing and post-storm visits are set to the house, and the findings are kept in one record.

Flat Roof Repair

Seams, drains and membrane laps are checked, then the failed area is rebuilt so water leaves the roof.

Storm Damage Roof Inspection

The whole roof is walked after a storm, damage is photographed and sorted, and the findings are written down.

Leak Diagnosis and Flashing Repair

The water path is traced from the ceiling back to the joint, and the flashing at that joint is rebuilt rather than sealed over.

Guides

Read before you book

FAQ

Gutter and Downspout Repair FAQs

Why does my gutter overflow only at one spot?

A single overflow point usually means a low spot in the run, a clogged outlet close by or a joint that has opened. Watching the gutter in rain shows which, and the repair is made at that spot rather than along the whole length.

Can a sagging gutter be fixed without replacing it?

Usually yes. The run is re-hung on new brackets, re-pitched and checked. Replacement is a better option when the gutter metal itself is split, badly corroded or too damaged to hold a seal, and the roofer should say which applies.

Does a gutter problem mean the roof is damaged too?

Not always, but water from an overflowing gutter can reach the edge of the covering, the fascia and the soffit. Those areas are checked when the gutter is repaired, and any damage found is recorded and dealt with in the same visit.

How often should gutters be cleared?

The right interval depends on the trees and the roof around the house and on how the gutter performs in the rain. A simple check after each big storm and at the change of seasons is a sensible routine, and the roofer can set a schedule for the specific house.

Where should the downspouts discharge?

Where the layout allows, the water should leave the building at least clear of the foundation and onto ground that falls away from the wall. Where a discharge would cross a neighbor's line or a shared alley, the route is changed before the work is set.

WhatsApp